![fujifilm pc autosave greyed out on camera fujifilm pc autosave greyed out on camera](https://cascable.se/help/ios/fujifilm-connection-guide/fuji-setup-wirelesssettings.png)
- Fujifilm pc autosave greyed out on camera how to#
- Fujifilm pc autosave greyed out on camera install#
- Fujifilm pc autosave greyed out on camera software#
- Fujifilm pc autosave greyed out on camera password#
- Fujifilm pc autosave greyed out on camera download#
Please note – without this software X-Pro2 will not be able to communicate with your PC and transfer files.
Fujifilm pc autosave greyed out on camera download#
Step 2: You need to download Fuji PC AutoSave from the Fujifilm support site: Now, if the Step 1 ended successfully, it is reasonable to think that all the rest will go also successfully, so now we can prepare the software needed for X-Pro2 to PC communication: the Fuji PC AutoSave. You need to do it only once – the above network definition will stay in your PC until you remove or reinstall Windows or revert Windows to the restoration point in time previous to the above action. If you have typed everything without any mistake and your Wi-Fi system in your PC works properly, you will see the following: A window will open with admin console – here you have to type: netsh wlan set hostednetwork mode=allow ssid=WIFI_FOR_FUJI key=qwert12345ytrewqĪnd press Enter. Select the Command Prompt (Admin) option. Go to the Windows icon in the corner of the screen and press RIGHT mouse button.
Fujifilm pc autosave greyed out on camera password#
Now, having defined name and password of the Wi-Fi, we have to tell Windows that it should setup such network. This my network is just for demonstration and will never be used again, so my password is simple and I can show it here: We want our network to be secure – this will be a network offered by our own PC, so nobody except of us should be able to connect to it. The second thing we need to define is the network access password. So for use in this article, I have defined the network name to be You need this step only if you want to create separate Wi-Fi network, supplied by your PC instead of home access point.įor this step we need to define (or invent) two things: name of the network – it must be meaningful to us as we will need to find it later on in the crowd of other available networks. Note: you DON’T need to do this step if you use the home Wi-Fi network. The following steps need to be done only once.
Fujifilm pc autosave greyed out on camera how to#
OK, so how to set up the communication? I use Windows 10, so it will be how to do it in case of Windows 10.įirst we need to enable a hot-spot, offered by our PC and enable PC to communicate with X-Pro2. Unless your PC is based on motherboard with integrated Wi-Fi, like for example ASUS X99 DELUXE I use.
Fujifilm pc autosave greyed out on camera install#
But if you use desktop PC, probably it does not have any Wi-Fi module, so you need to buy one and install it.
![fujifilm pc autosave greyed out on camera fujifilm pc autosave greyed out on camera](https://images.crutchfieldonline.com/ImageHandler/trim/750/457/products/2018/22/072/g072XT100G-F.jpg)
Please note – if you use notebook, you already have the needed Wi-Fi hardware. So I have enabled the Wi-Fi module built into my PC’s motherboard.
![fujifilm pc autosave greyed out on camera fujifilm pc autosave greyed out on camera](http://roguski.eu/wp-content/uploads/2016/07/20160731_141656.jpg)
In addition I prefer setting up a dedicated Wi-Fi network, just for Fuji, network I enable when needed and disable when not needed. But my PC is connected with cable to the switch, so the Wi-Fi communication between X-Pro2 and my PC didn’t work. So if we have a PC connected via Wi-Fi to the access point, it should work fine. I have observed this problem when PC was connected to the external switch as well as when the PC was connected with Ethernet cable to the switch built into the access point. It seems to be very similar to the Nikon UT-1 with WT-5 – in both cases I observed the same problem. I have checked it on my own – if X-Pro2 is connected to the access point but the PC is connected with Ethernet cable to the switch and then from switch to the access point, the communication will not work. When we use the existing home network, one thing is very important: due to poor Wi-Fi implementation in X-Pro2, both X-Pro2 and the PC must be connected directly to the same access point. For this purpose we can use either a home Wi-Fi or… we can create separate Wi-Fi network, served by the PC instead of home Wi-Fi access point and dedicated just for Fuji data transmission. I know that some people have issues establishing the connectivity with existing network, so here are some instructions, discoveries and thoughts.įirst thing: what network to connect to? This article is limited (by design) to only one option: transmitting the data from the body to the PC. I definitely prefer using Wi-Fi for this task. I use this option all the time as I don’t like removing cards from the body, guessing what is on which card, shuffling them in the reader.
![fujifilm pc autosave greyed out on camera fujifilm pc autosave greyed out on camera](https://i0.wp.com/www.macfilos.com/wp-content/uploads/2016/08/5c531af9ab383_img.jpg)
Fujifilm X-Pro2 gives us the ability to use Wi-Fi for communication.